FB体育官方

FB体育官方(中国)集团有限公司 FB体育官方(中国)集团有限公司
加工技术热线:18660816658
  • 您当前位置: 首页>>新闻动态>>行业动态抗倍特板施工时应该注意6点

    行业动态

    抗倍特板施工时应该注意6点

    来源://flashlightexpeditions.com/ 日期:2024-02-08 发布人:admin
    抗倍特板为乙烯基酯树脂是由双酚型或酚醛型环氧树脂与甲基丙烯酸反应得到的一类变性环氧树脂,通常被称为乙烯基酯、树脂,别名环氧丙烯酸树脂,为热固性树脂。接下来富美家抗倍特厂家根据多年的生产安装经验为大家介绍抗倍特板施工时应该注意哪些。
    Vinyl ester resin is a modified epoxy resin obtained by the reaction of bisphenol or phenolic epoxy resin with methacrylic acid. It is usually called vinyl ester, resin, also known as epoxy acrylic resin, and thermosetting resin. Next, according to many years of production and installation experience, Fumeijia Anti-Biot manufacturer will introduce what should be paid attention to during the construction of Anti-Biot plate.
    一、将泛水垫圈套入螺丝内以后,用电钻锁入檩条内,即完成抗倍特板的固定工作。
    1、 After inserting the flashing washer into the screw, lock it into the purlin with an electric drill, and then complete the fixation of the anti-magnification plate.
    二、抗倍特板在固定前先导孔,孔径要大于固定螺丝直径的6-9mm,以作为热胀冷缩之用。
    2、 The diameter of the pilot hole of the anti-magnification plate before fixing shall be 6-9mm larger than the diameter of the fixing screw for the purpose of thermal expansion and cold contraction.
    富美家抗倍特
    三、抗倍特板与钢板在纵向搭接时,要有200mm的重叠,并贴置两条止水带。
    3、 When the anti-magnification plate and steel plate are overlapped longitudinally, there should be 200mm overlap, and two waterstops should be pasted.
    四、抗倍特板固定时,要使用良好的泛水垫圈,使之介于螺丝与抗倍特板之间,以便于防水防尘。
    4、 When fixing the anti-multiplier plate, good flashing washer shall be used to make it between the screw and the anti-multiplier plate, so as to prevent water and dust.
    五、铺设完毕以后,预留出抗倍特板的位置,施工由檐口逐步往屋脊方向进行。抗倍特板直接扣在钢板的侧波峰上。
    5、 After the laying is completed, the position of the anti-magnification plate shall be reserved, and the construction shall be carried out gradually from the cornice to the ridge direction. The anti-magnification plate is directly buckled on the side wave crest of the steel plate.
    六、抗倍特板施工时,严禁脚直接踩在波峰上,以免抗倍特板开裂。要在抗倍特板的横向位置,放置一块1200mmx300mm{长x宽)防滑厚木板,脚踩在其上进行抗倍特板的导孔和固定螺丝工作。
    6、 During the construction of the anti-multiplier plate, it is strictly forbidden to step on the wave crest directly to avoid cracking of the anti-multiplier plate. Place a 1200mmx300mm (length x width) anti-skid thick plank at the transverse position of the anti-magnification plate, and step on it to conduct the guide hole and fixing screw work of the anti-magnification plate.
    抗倍特板施工的注意事项是抗倍特板固定时,要使用良好的泛水垫圈,使之介于螺丝与抗倍特板之间,以便于防水防尘。那么在对抗倍特板施工时,一定要注意以上这些。更多相关内容就来我们网站//flashlightexpeditions.com进行咨询吧!
    The precautions for the construction of the anti-multiplier plate are to use a good flashing washer between the screw and the anti-multiplier plate when the anti-multiplier plate is fixed, so as to prevent water and dust. Then, when constructing the double plate, we must pay attention to the above. Come to our website for more relevant content //flashlightexpeditions.com Consult!
    联系我们

    产品销售热线:18660816658

    技术方案咨询:18560211715

    仓库地址:济南市槐荫区河海工业园9号

    九江工厂:九江市江东FB体育官方3号

    台湾新竹工厂:台湾新竹

    泰国曼谷工厂:泰国曼谷

    关注我们
    FB体育官方(中国)集团有限公司 备案号: 网站地图 xml txt 流量统计

    截屏,微信识别二维码

    微信号:18660816658